Reversed-phase is one of those subjects where the details matter more than the headlines. This page pulls together the background, the mechanisms, and the practical points readers ask about most.
Last reviewed on 2026-06-10. Where a claim depends on a specific study, the study is described rather than over-claimed.
Detection in HPLC testing commonly relies on ultraviolet-visible absorbance, fluorescence, refractive index, or mass spectrometry. A diode array detector records full spectra across a wavelength range, which helps identify co-eluting peaks. Mass spectrometry provides mass-to-charge ratios and can confirm molecular identity at low concentrations. The choice of detector depends on analyte structure, required sensitivity, and whether quantitation or identification is the goal. No single detector works for every compound, and method development often compares responses before selecting one.
High-performance liquid chromatography is an analytical technique that separates components of a liquid sample by passing it through a packed column under pressure. A pump delivers a mobile phase at a controlled flow rate, and an injector introduces the sample into the stream. Differences in interaction with the stationary phase cause analytes to migrate at different rates. Detectors record elution as peaks, and a data system converts signals into a chromatogram. The method is suited to compounds that dissolve in a liquid and are not volatile enough for gas chromatography.
Reversed-phase chromatography dominates modern HPLC testing, using a nonpolar stationary phase such as chemically bonded octadecyl groups and a polar mobile phase of water mixed with organic solvent. Analytes partition between the mobile and stationary phases according to hydrophobicity. Gradient elution changes the mobile phase composition over time to separate compounds with a wide range of retention. Isocratic elution keeps the composition constant and is simpler for routine assays. Column temperature, pH, and flow rate influence selectivity, peak shape, and retention time, so these parameters are controlled during a validated method.
HPLC testing is not a single fixed procedure; it is a family of separation modes. Reversed-phase, normal-phase, ion-exchange, size-exclusion, and affinity chromatography each suit different analyte properties. Reversed-phase methods dominate because they handle many neutral and moderately polar compounds. Detection can be optical, electrochemical, or mass spectrometric, and the detector dictates what information is available. Coupling with mass spectrometry increases selectivity and enables identification when standards are unavailable. The technique cannot separate every mixture without adjustment.
HPLC testing is an analytical technique used to separate, identify, and quantify components in a liquid sample. It relies on a pressurized mobile phase that carries the sample through a column packed with stationary phase. Different compounds travel at different rates because of interactions with the stationary and mobile phases. The resulting signal versus time is a chromatogram. Peak position indicates identity under specified conditions, while peak area or height relates to amount.
Laboratories apply HPLC testing across pharmaceutical, food, environmental, and industrial chemistry. The method can measure active ingredients, impurities, additives, preservatives, and degradation products. Sample preparation often includes dilution, filtration, and sometimes extraction or derivatization. The choice of column, mobile phase, pH, temperature, and detector depends on the analytes and matrix. Results are compared with reference standards to assign identity and concentration. Method suitability is judged by resolution, precision, and accuracy.
| Property | Value | Notes |
|---|---|---|
| Separation mode | Reversed-phase | Most common for neutral and moderately polar analytes |
| Column particle size | 3–5 µm | Smaller particles improve resolution but raise backpressure |
| Mobile phase pH range | 2–8 | Silica-based columns may degrade outside this range |
| Typical flow rate | 1.0–2.0 mL/min | For analytical columns with 4.6 mm internal diameter |
| Common synonyms | HPLC, LC, high-pressure liquid chromatography | High-performance liquid chromatography is the standard expansion |
Separation modes differ by the chemistry of the stationary phase and the composition of the mobile phase. Reversed-phase testing uses a nonpolar column and polar solvents, making it common for pharmaceutical, environmental, and food analytes. Normal-phase testing uses a polar column and nonpolar solvents for compounds that are poorly retained in reversed-phase systems. Ion-exchange and ion-pair methods separate charged species, while size-exclusion methods sort molecules by hydrodynamic volume. Gradient elution changes solvent strength over time to resolve complex mixtures, and isocratic elution holds solvent composition constant for simpler assays.
Key performance measures include retention time, peak area, peak height, resolution, tailing factor, and plate count. Retention time helps identify a peak under fixed conditions, but confirmation often requires a second method or detector. Peak area and height relate to concentration through calibration curves, which may be linear or nonlinear depending on the detector response. Resolution describes separation between adjacent peaks, while tailing factor and plate count describe peak shape and column efficiency. Performance checks verify these values before and during a run to confirm that the instrument is performing within limits.
High-performance liquid chromatography testing separates components of a liquid sample by forcing a mobile phase through a packed column. The stationary phase inside the column interacts with analytes to different degrees, so each compound exits at a characteristic retention time. A pump delivers solvent at controlled flow and pressure, while an injector introduces a precise sample volume. Detectors such as ultraviolet-visible, fluorescence, refractive index, or mass spectrometric instruments record the separated bands. The resulting chromatogram provides qualitative and quantitative information about the mixture.
Regulatory and pharmacopeial texts shape how HPLC testing is performed and documented. The International Council for Harmonisation provides validation guidance, while pharmacopeias publish general chromatography chapters and monographs for specific materials. Accreditation standards such as ISO/IEC 17025 address laboratory competence and traceability. Inspectors may review instrument qualification, analyst training, reference material control, and electronic records. Open questions include how best to validate methods for new complex products and how to handle automated data processing. Laboratories generally resolve these issues through risk assessment, method lifecycle management, and documented scientific justification.
In quality control laboratories, HPLC testing supports batch release, raw material checks, stability studies, and impurity profiling. A validated method defines sample preparation, instrument settings, calibration, and acceptance criteria. Analysts compare results with specifications and investigate out-of-specification outcomes before a batch is approved. Documentation includes chromatograms, integration records, audit trails, and reagent details. Because results influence product decisions, laboratories follow formal quality systems and data integrity rules. The exact tests and limits depend on the material, its intended use, and the applicable regulatory framework.
System suitability testing is performed before and during analytical runs to confirm that the instrument and method are working as expected. Typical checks include retention time, peak area precision, resolution between critical pairs, tailing factor, and theoretical plate count. Acceptance criteria are set in the method or pharmacopeial monograph. If a suitability check fails, the run may be rejected and the instrument or sample preparation may need investigation. This practice helps prevent release of data from a system that has drifted out of control.
Quality control samples are inserted at intervals to monitor accuracy and precision throughout a batch. Blank samples detect contamination, while spiked samples assess recovery from the sample matrix. Calibration standards establish the relationship between detector response and concentration, and control samples are prepared independently from them whenever possible. Laboratories also participate in proficiency testing and maintain audit trails, instrument logs, and reagent records. Ongoing review of control charts can reveal trends before they cause out-of-specification results.
Profilins are proteins of molecular weights of roughly 14–19 kDa. They are present as single genes in yeast, insects, and worms, and as multiple genes in many other organisms including plants. In mammalian cells, four profilin isoforms have been discovered; profilin-I is expressed in most tissues while profilin-II is predominant in brain and kidney. Asgard archaea use profilins. Multiple eukaryotic diatom species lack profilins. Profilin is essential to host cell invasion by Toxoplasma gondii. Toxoplasma profilin is the specific pathogen-associated molecular pattern (PAMP) of TLRs 5, 11, and 12. Profilin enhances actin growth in two ways:
Klibanski became chief of the Neuroendocrine Unit at Massachusetts General Hospital, studying hormones and neuroendocrinology with a focus on hypopituitarism and pituitary tumors. Her clinical research has also examined the effects of hypothalamic and pituitary disorders on body composition and bone density, including bone loss associated with anorexia nervosa and growth hormone deficiency. In 1997, Klibanski became the first woman from Mass General's Department of Medicine to become a professor of medicine at Harvard. She has authored more than 350 peer-reviewed papers and book chapters and has received the Endocrine Society Clinical Investigator Award and the Clinical Endocrinology Trust Medal from the Society for Endocrinology. Klibanski has served on the National Institute of Diabetes and Digestive and Kidney Diseases Board of Counselors and the editorial board of the Journal of Clinical Endocrinology and Metabolism, and is a past president of the Pituitary Society. She established the Center for Faculty Development at Massachusetts General Hospital and mentored more than fifty women, for which she received the Endocrine Society's Outstanding Mentor Award.
Of 27 beef burger products tested, 37% were positive for horse DNA, and 85% were positive for pig DNA. Of 31 beef meal products tested, 21 were positive for pig DNA, but all were negative for horse DNA. Nineteen salami products were tested, but were negative for all foreign DNA. Of the 37% of beef products tested positive for horse DNA, Tesco's Everyday Value Beef Burgers tested at 29.1%. All other reported brands had less than 0.3% horse DNA. These products originated from Liffey Meats and Silvercrest Foods in Ireland, and from the Dalepak Hambleton food processing plant in the United Kingdom. Trace amounts of horse DNA were also found in raw ingredients imported from Spain and the Netherlands. Laboratory DNA investigations were requested by the authorities into possible donkey meat adulteration of minced meat products labelled as 100% beef. British company Primerdesign provided many of the tests to laboratories and companies wishing to test for contamination.
3-Dehydrocarnitine is an aliphatic quaternary ammonium betaine that is part of the carnitine family. At physiological pH of 7.3, the major species of 3-dehydrocarnitine is its zwitterionic form, the conjugate base of 3-dehydrocarnitinium. 3-Dehydrocarnitine is classified as a short-chain keto acid, as it has a carbon chain containing less than six carbon atoms. It is an intermediate in carnitine degradation and is formed from D- or L-carnitine. The enzymes responsible for the degradation of carnitine to 3-dehydrocarnitine are carnitine-3-dehydrogenase or (S)-carnitine-3-dehydrogenase.
In 2013, during the Long Shutdown 1, three ISOLDE buildings were demolished. They've been built again as a new single building with a new control room, a data storage room, three laser laboratories, a biology and materials laboratory, and a room for visitors. Another building extension for the MEDICIS project and several others equipped with electrical, cooling and ventilation systems to be used for the HIE-ISOLDE project in the future were also built. In addition, the robots which were installed for the handling of radioactive targets have been replaced with more modern robots. In 2015, for the first time, a radioactive isotope beam could be accelerated to an energy level of 4.3 MeV per nucleon in the ISOLDE facility thanks to the HIE-ISOLDE upgrades. In late 2017, the CERN-MEDICIS facility produced its first radioisotopes and by the end of 2020 had provided external nine hospitals and research facilities with 41 batches of radioisotopes. Phase 2 of the facility's HIE-ISOLDE upgrade was completed in 2018, which allows ISOLDE to accelerate radioactive beams up to 10 MeV per nucleon.
Sources: en.wikipedia.org
Synthesis of pre-vitamin D3 in the skin involves UVB radiation, which effectively penetrates only the epidermal layers of skin. 7-Dehydrocholesterol absorbs UV light most effectively at wavelengths between 295 and 300 nm and, thus, the production of vitamin D3 will occur primarily at those wavelengths. The two most important factors that govern the generation of pre-vitamin D3 are the quantity (intensity) and quality (appropriate wavelength) of the UVB irradiation reaching the 7-dehydrocholesterol deep in the stratum basale and stratum spinosum. Light-emitting diodes (LEDs) can be used to produce the radiation. Another important consideration is the quantity of 7-dehydrocholesterol present in the skin. Under normal circumstances, ample quantities of 7-dehydrocholesterol (about 25–50 μg/cm2 of skin) are available in the stratum spinosum and stratum basale of human skin to meet the body's vitamin D requirements. 7-DHC insufficiency has been proposed as an alternate cause for Vitamin D deficiency.
As filaments grow, the pool of available G-actin molecules is managed by G-actin-binding proteins such as profilin and thymosin β-4. Profilin ensures a supply of available actin-ATP by binding to ADP-bound G-actin and promoting the exchange of ADP for ATP. Profilin's binding to the actin molecule physically blocks its addition to a filament's (−) end, but permits it to join the (+) end. Once the actin-ATP has joined the filament, profilin releases it. As formins promote the nucleation and extension of new actin filaments, they recruit profilin to the area, increasing the local concentration of actin-ATP to boost filament growth. In contrast, thymosin β-4 binds and sequesters actin-ATP, preventing it from joining a microfilament. Once an actin fiber is established, the dynamics of its growth or collapse are influenced by numerous proteins. Existing strands can be interrupted by filament cleaving proteins, such as cofilin and gelsolin. Cofilin binds along two actin-ADP molecules in a filament, forcing a movement that destabilizes the filament and causes it to break. Gelsolin inserts itself between actin molecules in a filament, disrupting the filament. After the filament breaks, gelsolin remains attached to the new (+) end, preventing it from growing, thus forcing its disassembly.
Afucosylated monoclonal antibodies are monoclonal antibodies engineered so that the oligosaccharides in the Fc region of the antibody do not have any fucose sugar units. When antibodies are afucosylated, antibody-dependent cellular cytotoxicity (ADCC) is increased. Most approved monoclonal antibodies are of the IgG1 isotype, where two N-linked biantennary complex-type oligosaccharides are bound to the Fc region. The Fc region exercises the effector function of ADCC through its interaction with leukocyte receptors of the FcγR family. ADCC is important in the efficacy of cancer antibodies, but with many approved cancer antibodies there is less ADCC than could be desired due to nonspecific IgG competing with the drugs for binding to FcγIIIa on natural killer cells. Afucosylated monoclonal antibodies overcome this problem through improved FcγIIIa binding.
Naturally, it is produced in the human placenta by the syncytiotrophoblast. Like any other gonadotropins, it can be extracted from the urine of pregnant women or produced from cultures of genetically modified cells using recombinant DNA technology. In Pubergen, Pregnyl, Follutein, Profasi, Choragon and Novarel, it is extracted from the urine of pregnant women. In Ovidrel, it is produced with recombinant DNA technology.
Sources: en.wikipedia.org
HPLC testing separates and quantifies components in a liquid sample. It is used to check identity, purity, concentration, or stability. The technique works best for compounds that dissolve and are not easily vaporized.
The pump maintains a steady flow rate and pressure, which keeps retention times reproducible. Pulsation or flow errors can shift peaks and distort quantitation. Modern pumps use feedback control to reduce these variations.
HPLC alone usually separates compounds but does not always identify them. Retention time matching with a known standard provides tentative identification. Coupling HPLC to mass spectrometry adds mass information that supports structural identification.
It measures the presence and amount of one or more compounds in a liquid sample. Separation occurs in a column, and detection produces a signal proportional to concentration. Identification usually requires comparison with a known reference standard under the same conditions.