Everything below concerns stationary phase. We keep the language plain, cite what the science says, and separate well-supported claims from open questions.
Last reviewed on 2026-03-22. Where a claim depends on a specific study, the study is described rather than over-claimed.
Quality control samples are inserted at intervals to monitor accuracy and precision throughout a batch. Blank samples detect contamination, while spiked samples assess recovery from the sample matrix. Calibration standards establish the relationship between detector response and concentration, and control samples are prepared independently from them whenever possible. Laboratories also participate in proficiency testing and maintain audit trails, instrument logs, and reagent records. Ongoing review of control charts can reveal trends before they cause out-of-specification results.
Method validation demonstrates that an HPLC procedure is suitable for its intended purpose. Common validation parameters include accuracy, precision, specificity, linearity, range, limit of detection, limit of quantification, and robustness. Accuracy reflects agreement with a reference value, while precision describes repeatability under defined conditions. Specificity shows whether the method can measure the analyte in the presence of impurities or matrix components. Validation documents are reviewed before a method is used for routine testing or regulatory submissions.
System suitability testing is performed before and during analytical runs to confirm that the instrument and method are working as expected. Typical checks include retention time, peak area precision, resolution between critical pairs, tailing factor, and theoretical plate count. Acceptance criteria are set in the method or pharmacopeial monograph. If a suitability check fails, the run may be rejected and the instrument or sample preparation may need investigation. This practice helps prevent release of data from a system that has drifted out of control.
Routine HPLC testing depends on controlled reagents, calibrated instruments, and documented procedures. Columns degrade over time, so retention times and peak shapes are monitored for drift. Mobile phases are filtered and degassed to prevent pump damage and detector noise. Reference standards must be traceable and stored under suitable conditions. Data handling systems record injections, calculations, and audit trails. Quality control samples interspersed with unknowns help detect errors during a run.
Developing an HPLC method begins with defining the purpose, such as quantifying a main component, measuring impurities, or confirming identity. Analysts select separation mode, column, mobile phase, detection, and sample preparation based on analyte properties and matrix. Experiments vary solvent strength, pH, buffer type, and temperature to achieve resolution between critical peaks. The goal is a robust method that produces reliable results across instruments and operators. Method development often involves trial runs and statistical optimization.
Validation demonstrates that a method is suitable for its intended use. Typical performance characteristics include accuracy, precision, specificity, linearity, range, limit of detection, limit of quantitation, and robustness. Regulators and standards organizations provide frameworks, but specific requirements depend on the application and jurisdiction. System suitability tests are run before sample analysis to confirm resolution, peak symmetry, retention time repeatability, and sensitivity. A validated method is not permanently fixed; changes may require partial or full revalidation.
| Property | Value | Notes |
|---|---|---|
| Validation parameter | Accuracy | Closeness to a reference value. |
| Validation parameter | Precision | Repeatability or intermediate precision. |
| Validation parameter | Linearity | Proportional response across a range. |
| System suitability check | Resolution | Separation between adjacent peaks. |
| Quality control tool | Control chart | Tracks results over time for trends. |
Data handling and documentation are central to HPLC quality control. Electronic systems should have audit trails that record changes to methods, sequences, and results. Integration parameters, such as peak baseline and threshold, can affect reported areas and must be defined in advance. Out-of-specification results trigger a structured investigation that may include reanalysis, instrument checks, and review of sample preparation. Regulatory inspections often examine raw data, audit trails, and training records to verify that reported results are traceable and reliable.
Method validation establishes that an HPLC procedure is suitable for its intended use. Key parameters include accuracy, precision, specificity, linearity, range, limit of detection, limit of quantitation, and robustness. Accuracy measures agreement with a true or accepted value, while precision describes repeatability and intermediate precision. Specificity confirms that the method measures the analyte without interference from impurities, degradants, or excipients. Validation is documented in a protocol and report, and acceptance criteria are set before experiments begin. Regulatory guidance varies by region, but the general principles are widely harmonized.
System suitability testing is performed before and during analytical runs to confirm that the instrument and method are working as expected. Common checks include retention time, peak area, resolution between critical pairs, tailing factor, and theoretical plate count. Results are compared with predefined limits, and a failed check requires investigation before sample results are reported. Quality control samples at low, middle, and high concentrations are injected at intervals to monitor accuracy and precision. Blank injections detect carryover and contamination, while control charts track performance over time.
Key performance measures include retention time, peak area, peak height, resolution, tailing factor, and plate count. Retention time helps identify a peak under fixed conditions, but confirmation often requires a second method or detector. Peak area and height relate to concentration through calibration curves, which may be linear or nonlinear depending on the detector response. Resolution describes separation between adjacent peaks, while tailing factor and plate count describe peak shape and column efficiency. Performance checks verify these values before and during a run to confirm that the instrument is performing within limits.
High-performance liquid chromatography testing separates components of a liquid sample by forcing a mobile phase through a packed column. The stationary phase inside the column interacts with analytes to different degrees, so each compound exits at a characteristic retention time. A pump delivers solvent at controlled flow and pressure, while an injector introduces a precise sample volume. Detectors such as ultraviolet-visible, fluorescence, refractive index, or mass spectrometric instruments record the separated bands. The resulting chromatogram provides qualitative and quantitative information about the mixture.
Separation modes differ by the chemistry of the stationary phase and the composition of the mobile phase. Reversed-phase testing uses a nonpolar column and polar solvents, making it common for pharmaceutical, environmental, and food analytes. Normal-phase testing uses a polar column and nonpolar solvents for compounds that are poorly retained in reversed-phase systems. Ion-exchange and ion-pair methods separate charged species, while size-exclusion methods sort molecules by hydrodynamic volume. Gradient elution changes solvent strength over time to resolve complex mixtures, and isocratic elution holds solvent composition constant for simpler assays.
Instrumentation includes a solvent delivery system, an autosampler, a column oven, and one or more detectors. Reversed-phase columns with chemically modified silica are widely used, but normal-phase, ion-exchange, size-exclusion, and affinity modes exist for specific separations. Detectors may rely on ultraviolet absorbance, fluorescence, refractive index, or mass spectrometry. Column temperature, mobile phase composition, and flow rate are adjusted to improve resolution. System pressure is monitored because rising pressure can indicate column blockage or deteriorating packing.
Separation performance depends on particle size, pore size, column length, and the chemistry of the stationary phase. Smaller particles generally improve efficiency but require higher pressure and suitable instrumentation. The mobile phase often contains buffers and organic solvents that influence retention and selectivity. Testing labs select conditions based on the analytes, sample matrix, and required sensitivity. Method development frequently involves screening several columns and solvent mixtures before a final set of conditions is chosen.
High-performance liquid chromatography is an analytical technique that separates components in a liquid sample by passing them through a packed column under pressure. A pump delivers a mobile phase at a controlled flow rate, and an injector introduces the sample into the stream. Differences in how analytes partition between the mobile phase and the stationary phase cause them to exit the column at different times. Detection then records a signal proportional to the amount of each separated substance. The resulting chromatogram provides retention times and peak areas for identification and quantification.
Detection in HPLC testing commonly relies on ultraviolet-visible absorbance, fluorescence, refractive index, or mass spectrometry. UV detection is widely used because many organic compounds absorb light, but it requires a chromophore. Mass spectrometry provides mass-based identification and high sensitivity for trace analytes. Each detector has trade-offs in selectivity, cost, and compatibility with mobile phases. Quantification typically uses calibration curves prepared from reference standards. Results are reported as concentration, purity, or presence above a limit.
HPLC testing separates dissolved compounds by passing a liquid sample through a column packed with stationary phase. A pump delivers mobile phase at controlled flow, and the sample components interact differently with stationary and mobile phases. Compounds that spend more time in mobile phase elute earlier; those retained by stationary phase elute later. Detectors record elution as peaks, and peak area or height relates to amount. This mechanism underpins quantitative analysis of mixtures.
In 1930, safety glass became standard on all Ford cars. In the 1930s, plastic surgeon Claire L. Straith and physician C. J. Strickland advocated the use of seat belts and padded dashboards. Strickland founded the Automobile Safety League of America. In 1934, GM performed the first barrier crash test. In 1936, the Hudson Terraplane came with the first back-up brake system. Should the hydraulic brakes fail, the brake pedal would activate a set of mechanical brakes for the back wheels. In 1937, Chrysler, Plymouth, DeSoto, and Dodge added such items as a flat, smooth dash with recessed controls, rounded door handles, a windshield wiper control made of rubber, and the back of the front seat heavily padded to provide protection for rear passengers.
The amplitude of SHOC2-mediated ERK1/2 signals has been proposed to be regulated by differential regulation of RAF activation at the plasma membrane and internalized endosome compartment as well an alternative model proposing post-translational modifications. SHOC2 ubiquitination mediated by HUWE1 is triggered by growth factor activation of the ERK1/2 pathway and is a prerequisite for the subsequent ubiquitination of the RAF-1 kinase associated with SHOC2. However, the current data has yet to address how these ubiquitin modifications regulate the SHOC2 holophosphatase function to reduce the amplitude of RAF-ERK1/2 signals. It has been shown that activity that results in lipidation (specifically Myristoylation) of SHOC2 can cause Noonan syndrome. SHOC2 has been shown to interact with the catalytic phosphatase subunit PP1C and MRAS as well as canonical RAS isoforms (H/K/NRAS). The ternary complex SHOC2-RAS-PP1C functions to dephosphorylate an inhibitory phosphorylation site ('S259') on RAF family proteins to enable MAPK signaling.
Albert Lester Lehninger (February 17, 1917 – March 4, 1986) was an American chemist in the field of bioenergetics. He made fundamental contributions to the current understanding of metabolism at a molecular level. In 1948, he discovered, with Eugene P. Kennedy, that mitochondria are the site of oxidative phosphorylation in eukaryotes, which ushered in the modern study of energy transduction. He is the author of a number of classic texts, including Biochemistry, The Mitochondrion, Bioenergetics and, most notably, his series Principles of Biochemistry. This last is a widely used text for introductory biochemistry courses at the college and university levels. Lehninger was born in Bridgeport, Connecticut, US. He earned his BA in English from Wesleyan University (1939) and went on to earn both his MA (1940) and PhD (1942) at the University of Wisconsin–Madison. His doctoral research involved the metabolism of acetoacetate and fatty acid oxidation by liver cells.
The carbon atom next to the carboxyl group is called the α–carbon. In proteinogenic amino acids, it bears the amine and the R group or side chain specific to each amino acid, as well as a hydrogen atom. With the exception of glycine, for which the side chain is also a hydrogen atom, the α–carbon is stereogenic. All chiral proteinogenic amino acids have the L configuration, and can therefore be referred to as L-amino acids. They are "left-handed" enantiomers, which refers to the stereoisomers of the alpha carbon. A few D-amino acids ("right-handed") have been found in nature, e.g., in bacterial envelopes, as a neuromodulator (D-serine), and in some antibiotics. Rarely, D-amino acid residues are found in proteins, and are converted from the L-amino acid as a post-translational modification.
Biochemistry is the study of chemical processes within and relating to living organisms. Molecular biology is the branch of biology that seeks to understand the molecular basis of biological activity in and between cells. It is centered largely on the study of nucleic acids (such as DNA and RNA) and proteins. It examines the structure, function, and interactions of these macromolecules as they orchestrate processes such as replication, transcription, translation, protein synthesis, and complex biomolecular interactions. In 1953, the Miller–Urey experiment showed that organic compounds could be synthesized abiotically within a closed system mimicking the conditions of early Earth, thus suggesting that complex organic molecules could have arisen spontaneously in early Earth in the process of abiogenesis.
Sources: en.wikipedia.org
GCaMP consists of three key domains: an M13 domain at the N-terminus, a calmodulin (CaM) domain at the C-terminus, and a GFP domain in the center. The GFP domain is circularly permuted such that the native N- and C-termini are fused together by a six-amino-acid linking sequence, and the GFP sequence is split in the middle, creating new N- and C-termini that connect to the M13 and CaM domains. In the absence of Ca2+, the GFP chromophore is exposed to water and exists in a protonated state with minimal fluorescence intensity. Upon Ca2+ binding, the CaM domain undergoes a conformational change and tightly binds to the M13 domain alpha helix, preventing water molecules from accessing the chromophore. As a result, the chromophore rapidly deprotonates and converts into an anionic form that fluoresces brightly, similar to native GFP.
Klibanski became chief of the Neuroendocrine Unit at Massachusetts General Hospital, studying hormones and neuroendocrinology with a focus on hypopituitarism and pituitary tumors. Her clinical research has also examined the effects of hypothalamic and pituitary disorders on body composition and bone density, including bone loss associated with anorexia nervosa and growth hormone deficiency. In 1997, Klibanski became the first woman from Mass General's Department of Medicine to become a professor of medicine at Harvard. She has authored more than 350 peer-reviewed papers and book chapters and has received the Endocrine Society Clinical Investigator Award and the Clinical Endocrinology Trust Medal from the Society for Endocrinology. Klibanski has served on the National Institute of Diabetes and Digestive and Kidney Diseases Board of Counselors and the editorial board of the Journal of Clinical Endocrinology and Metabolism, and is a past president of the Pituitary Society. She established the Center for Faculty Development at Massachusetts General Hospital and mentored more than fifty women, for which she received the Endocrine Society's Outstanding Mentor Award.
In Taiwan, the Taiwan Transportation Safety Board (TTSB) is the independent government agency that is responsible for major transportation accident investigations. TTSB's predecessor was ASC, which was established in 1998. TTSB is under the administration of the Executive Yuan and independent from Civil Aviation Administration. The TTSB consisted of five to seven board members, including a chairman and a vice chairman, appointed by the Premier. The managing director of TTSB manages the day-to-day function of the organization, including accident investigations. In the United Kingdom, the agency responsible for investigation of civilian air crashes is the Air Accidents Investigation Branch (AAIB) of the Department for Transport. Its purpose is to establish the circumstances and causes of the accident and to make recommendations for their future avoidance.
There are numerous theories as to the exact cause and mechanism in type 2 diabetes. Central obesity is known to predispose individuals for insulin resistance. Abdominal fat is especially active hormonally, secreting a group of hormones called adipokines that may possibly impair glucose tolerance. But adiponectin, an anti-inflammatory adipokine, which is found in lower concentration in obese and diabetic individuals has shown to be beneficial and protective in type 2 diabetes mellitus (T2DM). Insulin resistance is a major feature of diabetes mellitus type 2, and central obesity is correlated with both insulin resistance and T2DM itself. Increased adiposity (obesity) raises serum resistin levels, which in turn directly correlate to insulin resistance. Studies have also confirmed a direct correlation between resistin levels and T2DM. And it is waistline adipose tissue (central obesity) which seems to be the foremost type of fat deposits contributing to rising levels of serum resistin. Conversely, serum resistin levels have been found to decline with decreased adiposity following medical treatment.
When measured by fatalities per person transported, however, buses are the safest form of transportation. The number of air travel fatalities per person are surpassed only by bicycles and motorcycles. This statistic is used by the insurance industry when calculating insurance rates for air travel. For every billion kilometers traveled, trains have a fatality rate that is 12 times higher than that of air travel, and the fatality rate for automobiles is 62 times greater than for air travel. By contrast, for every billion journeys taken, buses are the safest form of transportation; using this measure, air travel is three times more dangerous than car transportation, and almost 30 times more dangerous than travelling by bus. A 2007 study by Popular Mechanics magazine found that passengers sitting at the back of an aeroplane are 40% more likely to survive a crash than those sitting at the front. The article quotes Boeing, the FAA, and a website on aircraft safety, all of which claim that there is no "safest" seat. The study examined 20 crashes, not taking into account the developments in safety after those accidents. However, a flight data recorder is usually mounted in the aircraft's empennage (tail section) where it is more likely to survive a severe crash. Between 1983 and 2000, the survival rate for people in U.S. plane crashes was greater than 95 percent.
Sources: en.wikipedia.org
Osmotic stress is defined as difficulty maintaining proper fluids in the cell within a hypertonic or hypotonic environment. MAAs accumulate within a cell's cytoplasm and contribute to the osmotic pressure within a cell, thus relieving pressure from salt stress in a hypertonic environment. As evidence of this, MAAs are seldom found in large quantities in cyanobacteria living in freshwater environments. However, in saline and hypertonic environments, cyanobacteria often contain high concentrations of MAAs. The same phenomenon was noted for some halotolerant fungi. But, the concentration of MAAs within cyanobacteria living in hyper-saline environments is far from the amount required to balance the salinity. Therefore, additional osmotic solutes must be present as well.
The major limitation in the development of artificial WBCs is the translation of the technologies into clinical approval and use. Other limitations include the availability of technology necessary to produce artificial WBCs, variability in yield, and difficulties in purifying the particles necessary for standard clinical use. Some studies have also found that these particles may unintentionally target other tissues that are otherwise healthy. The delivery of the therapies faces some difficulties in that too rapid administration might cause systemic side effects, whereas a too slow release would be less effective. A major limitation to polymersomes is that a select number of polymers such as polyethylene glycol and poly(lactic-co-glycolic acid) are approved by the FDA for clinical use. Nanoghosts, or more generally membrane-coated nanoparticles, experience limitations in that cells will have varying degrees of proteins present in their membranes, creating variability and lack of stability in those products. There also is the risk that membrane proteins essential to the biomimetic function of the nanoghosts can become denatured in the manufacturing and storage process. Overall, more studies need to be done on these biomimetic solutions to verify efficacy and safety.
CLE peptides are coded by the CLE genes. These peptides vary in structure, with each peptide structure performing a different job within the plant. The minimal length of functioning CLE peptides has been found to be 12 amino acids with several critical residues. There are two different peptide structures that are found within the plant and they are A-type and B-type. When A-type hormones are secreted the plant slows down the rate of root growth whereas the secretion of B-type peptides effects the vascular growth of the plant. The secretion of A-type peptides speeds up the vascular development of the plant that is mediated by the B-type peptides. This suggests that these two types of peptides work together to regulate the growth of the plant. The specific peptides are: A-type peptides B-type peptides CLE 41/44/TDIF CLE 42 CLE 43 CLE 46
Upregulation of receptors is the increase in receptor number or sensitivity of receptors. The receptors involved in functional antagonism are regulated in sensitivity, number and location. Therefore, changes in receptors are common. Using a long-term antagonist drug or continuous exposure to an antagonist may cause the upregulation and hypersensitivity of receptors, which means an increase in the number and sensitivity of receptors. The increase in the number of receptors is due to the increased expression of receptors after prolonged inhibition. The upregulation of receptors is important in the clinical aspect. One example of upregulation of receptors is the upregulation of β-receptors caused by β receptor antagonists (also called β-blocker). The prolonged use of β-blockers results in the blockade of β-receptors, causing cells (mainly myocardial cells) to increase their expression of β-receptor. After removing the blockage, more receptors available for stimulation, resulting in higher sensitivity of β-receptors called the hypersensitivity of β-receptors. Abrupt discontinuation of β-blocker may potentially aggravate coronary artery disease, tachycardia, or even sudden cardiac death. Therefore, to prevent the adverse effects, doses of β-blocker must be reduced gradually over 10–14 days.
Genetically modified organism History of biotechnology An Asilomar Moment Archived 10 July 2013 at the Wayback Machine Original Asilomar Genetics Guidelines “Asilomar Conference.” Provides another summary of the Asilomar Conference. The Basics of Recombinant DNA provides an introduction to the science behind recombinant DNA. The Recombinant DNA Debate Archived 31 March 2007 at the Wayback Machine provides more details about the history of the debate surrounding the use of recombinant DNA technology. “Paul Berg: The 1980 Nobel Prize in Chemistry – Autobiography.” Provides an autobiography about Paul Berg. Science History Institute: The story of the 1975 Asilomar Conference on Recombinant DNA
Sources: en.wikipedia.org
Method validation is the documented process of showing that an HPLC procedure produces reliable results for a defined purpose. It examines parameters such as accuracy, precision, specificity, linearity, and robustness. Regulators and quality systems often require validation before routine use.
System suitability is a set of checks run on the chromatographic system before sample analysis. It confirms that resolution, peak shape, retention time, and response meet predefined limits. Failure can invalidate the run and trigger corrective action.
Blank injections reveal peaks or baseline disturbances that come from solvents, reagents, or the instrument rather than the sample. They help distinguish contamination from actual analyte signals. Comparing blanks with sample runs supports accurate interpretation.
It is a set of checks performed before or during an HPLC run to confirm the system works as expected. Parameters may include resolution, tailing factor, theoretical plates, and retention time precision. Failure can trigger maintenance, method adjustment, or repeat analysis.