The short version of data integrity fits in a sentence. The long version — which is the one that helps — is below.
This page was last updated on 2025-11-02 and is reviewed periodically as new material appears.
Reversed-phase chromatography dominates modern HPLC testing, using a nonpolar stationary phase such as chemically bonded octadecyl groups and a polar mobile phase of water mixed with organic solvent. Analytes partition between the mobile and stationary phases according to hydrophobicity. Gradient elution changes the mobile phase composition over time to separate compounds with a wide range of retention. Isocratic elution keeps the composition constant and is simpler for routine assays. Column temperature, pH, and flow rate influence selectivity, peak shape, and retention time, so these parameters are controlled during a validated method.
Detection in HPLC testing commonly relies on ultraviolet-visible absorbance, fluorescence, refractive index, or mass spectrometry. A diode array detector records full spectra across a wavelength range, which helps identify co-eluting peaks. Mass spectrometry provides mass-to-charge ratios and can confirm molecular identity at low concentrations. The choice of detector depends on analyte structure, required sensitivity, and whether quantitation or identification is the goal. No single detector works for every compound, and method development often compares responses before selecting one.
High-performance liquid chromatography is an analytical technique that separates components of a liquid sample by passing it through a packed column under pressure. A pump delivers a mobile phase at a controlled flow rate, and an injector introduces the sample into the stream. Differences in interaction with the stationary phase cause analytes to migrate at different rates. Detectors record elution as peaks, and a data system converts signals into a chromatogram. The method is suited to compounds that dissolve in a liquid and are not volatile enough for gas chromatography.
Key performance measures include retention time, peak area, peak height, resolution, tailing factor, and plate count. Retention time helps identify a peak under fixed conditions, but confirmation often requires a second method or detector. Peak area and height relate to concentration through calibration curves, which may be linear or nonlinear depending on the detector response. Resolution describes separation between adjacent peaks, while tailing factor and plate count describe peak shape and column efficiency. Performance checks verify these values before and during a run to confirm that the instrument is performing within limits.
High-performance liquid chromatography testing separates components of a liquid sample by forcing a mobile phase through a packed column. The stationary phase inside the column interacts with analytes to different degrees, so each compound exits at a characteristic retention time. A pump delivers solvent at controlled flow and pressure, while an injector introduces a precise sample volume. Detectors such as ultraviolet-visible, fluorescence, refractive index, or mass spectrometric instruments record the separated bands. The resulting chromatogram provides qualitative and quantitative information about the mixture.
Separation modes differ by the chemistry of the stationary phase and the composition of the mobile phase. Reversed-phase testing uses a nonpolar column and polar solvents, making it common for pharmaceutical, environmental, and food analytes. Normal-phase testing uses a polar column and nonpolar solvents for compounds that are poorly retained in reversed-phase systems. Ion-exchange and ion-pair methods separate charged species, while size-exclusion methods sort molecules by hydrodynamic volume. Gradient elution changes solvent strength over time to resolve complex mixtures, and isocratic elution holds solvent composition constant for simpler assays.
| Property | Value | Notes |
|---|---|---|
| Separation mode | Reversed-phase | Most common for neutral and moderately polar analytes |
| Column particle size | 3–5 µm | Smaller particles improve resolution but raise backpressure |
| Mobile phase pH range | 2–8 | Silica-based columns may degrade outside this range |
| Typical flow rate | 1.0–2.0 mL/min | For analytical columns with 4.6 mm internal diameter |
| Common synonyms | HPLC, LC, high-pressure liquid chromatography | High-performance liquid chromatography is the standard expansion |
Quality control samples are inserted at intervals to monitor accuracy and precision throughout a batch. Blank samples detect contamination, while spiked samples assess recovery from the sample matrix. Calibration standards establish the relationship between detector response and concentration, and control samples are prepared independently from them whenever possible. Laboratories also participate in proficiency testing and maintain audit trails, instrument logs, and reagent records. Ongoing review of control charts can reveal trends before they cause out-of-specification results.
Method validation demonstrates that an HPLC procedure is suitable for its intended purpose. Common validation parameters include accuracy, precision, specificity, linearity, range, limit of detection, limit of quantification, and robustness. Accuracy reflects agreement with a reference value, while precision describes repeatability under defined conditions. Specificity shows whether the method can measure the analyte in the presence of impurities or matrix components. Validation documents are reviewed before a method is used for routine testing or regulatory submissions.
Laboratories apply HPLC testing across pharmaceutical, food, environmental, and industrial chemistry. The method can measure active ingredients, impurities, additives, preservatives, and degradation products. Sample preparation often includes dilution, filtration, and sometimes extraction or derivatization. The choice of column, mobile phase, pH, temperature, and detector depends on the analytes and matrix. Results are compared with reference standards to assign identity and concentration. Method suitability is judged by resolution, precision, and accuracy.
HPLC testing is not a single fixed procedure; it is a family of separation modes. Reversed-phase, normal-phase, ion-exchange, size-exclusion, and affinity chromatography each suit different analyte properties. Reversed-phase methods dominate because they handle many neutral and moderately polar compounds. Detection can be optical, electrochemical, or mass spectrometric, and the detector dictates what information is available. Coupling with mass spectrometry increases selectivity and enables identification when standards are unavailable. The technique cannot separate every mixture without adjustment.
HPLC testing is an analytical technique used to separate, identify, and quantify components in a liquid sample. It relies on a pressurized mobile phase that carries the sample through a column packed with stationary phase. Different compounds travel at different rates because of interactions with the stationary and mobile phases. The resulting signal versus time is a chromatogram. Peak position indicates identity under specified conditions, while peak area or height relates to amount.
In quality control laboratories, HPLC testing supports batch release, raw material checks, stability studies, and impurity profiling. A validated method defines sample preparation, instrument settings, calibration, and acceptance criteria. Analysts compare results with specifications and investigate out-of-specification outcomes before a batch is approved. Documentation includes chromatograms, integration records, audit trails, and reagent details. Because results influence product decisions, laboratories follow formal quality systems and data integrity rules. The exact tests and limits depend on the material, its intended use, and the applicable regulatory framework.
Method validation examines whether an HPLC procedure is suitable for its intended purpose. Common parameters include accuracy, precision, specificity, linearity, range, detection limit, quantification limit, and robustness. Accuracy describes closeness to a true or accepted value, while precision describes agreement among repeated measurements. Specificity shows whether the method can measure the analyte without interference from related substances. Robustness tests small deliberate changes in flow, temperature, or solvent composition. Validation is not a one-time event; methods may need partial revalidation after changes to instruments, columns, sample handling, or specification limits. Regulatory guidance provides frameworks, but some details remain method-specific.
The 5,10-methenyltetrahydromethanopterin hydrogenase (or Hmd), the so-called iron-sulfur cluster-free hydrogenase, is an enzyme found in methanogenic archea such as Methanothermobacter marburgensis. It was discovered and first characterized by the Thauer group at the Max Planck Institute in Marburg. Hydrogenases are enzymes that either reduce protons or oxidize molecular dihydrogen.
Human chorionic gonadotropin is a glycoprotein composed of 237 amino acids with a molecular mass of 36.7 kDa, approximately 14.5kDa αhCG and 22.2kDa βhCG. It is heterodimeric, with an α (alpha) subunit identical to that of luteinizing hormone (LH), follicle-stimulating hormone (FSH), thyroid-stimulating hormone (TSH), and a β (beta) subunit that is unique to hCG. The α (alpha) subunit is 92 amino acids long. The β-subunit of hCG gonadotropin (beta-hCG) contains 145 amino acids, encoded by six highly homologous genes that are arranged in tandem and inverted pairs on chromosome 19q13.3 - CGB (1, 2, 3, 5, 7, 8). It is known that CGB7 has a sequence slightly different from that of the others. The two subunits create a small hydrophobic core surrounded by a high surface area-to-volume ratio: 2.8 times that of a sphere. The vast majority of the outer amino acids are hydrophilic. beta-hCG is mostly similar to beta-LH, with the exception of a Carboxy Terminus Peptide (beta-CTP) containing four glycosylated serine residues that is responsible for hCG's longer half-life.
At low concentrations of TNP-ATP (≤1 μM), fluorescent intensity is proportional to the concentration of TNP added. However, at concentrations exceeding 1 μM, inner filter effects cause this relationship to no longer be linear. To correct this, researchers must determine the ratio of the predicted theoretical fluorescence intensity (assuming linearity) to the observed fluorescence intensity and then apply this correction factor. However, in most cases, researchers will try to keep the concentration of TNP to lower than 1 μM. To determine binding affinities, TNP-ATP is added to a solution and then titrated with protein. This produces a saturation curve from which the binding affinity can be determined. The number of binding sites may also be determined through this saturation curve by looking to see if there are sudden changes in slope. One can also titrate a fixed amount of protein with increasing additions of TNP-ATP to obtain a saturation curve. To do so, however, may get complicated due to the inner filter effects that will need to be corrected for. To determine dissociation constants, TNP-ATP can be competed off of a protein with ATP. The value of the dissociation constant Kd for a single-site binding can then be obtained by applying the Langmuir equation for a curve fit:
In 1979 Zaffaroni was awarded the Chemical Pioneer Award by the American Institute of Chemists In 1995, he received the National Medal of Technology from President Bill Clinton for his contributions to the pharmaceutical and biotechnology industries. In 2004, he was one of the recipients of the Winthrop-Sears Medal from the Chemical Heritage Foundation and The Chemists’ Club, with George Rosenkranz. In 2005 he received the Bower Award for Business Leadership from the Franklin Institute for his creation of new biochemical processes and drug delivery technologies. In 2005 he was awarded the Gregory Pincus Award from the Worcester Foundation. In 2006, he received the Biotechnology Heritage Award, from the Biotechnology Industry Organization (BIO) and the Chemical Heritage Foundation.
Aβ is formed after sequential cleavage of the amyloid precursor protein (APP), a transmembrane glycoprotein of undetermined function. APP can be cleaved by the proteolytic enzymes α-, β- and γ-secretase; Aβ protein is generated by successive action of the β and γ secretases. The γ secretase, which produces the C-terminal end of the Aβ peptide, cleaves within the transmembrane region of APP and can generate a number of isoforms of 30–51 amino acid residues in length. The most common isoforms are Aβ40 and Aβ42; the longer form is typically produced by cleavage that occurs in the endoplasmic reticulum, while the shorter form is produced by cleavage in the trans-Golgi network.
Sources: en.wikipedia.org
Colony-forming unit-fibroblast Mesenchymal stem cell / marrow stromal cell Chondrocyte Hypertrophic chondrocyte Mesenchymal (mesoderm origin) stem cells are undifferentiated, meaning they can differentiate into a variety of generative cells commonly known as osteochondrogenic (or osteogenic, chondrogenic, osteoprogenitor, etc.) cells. When referring to bone, or in this case cartilage, the originally undifferentiated mesenchymal stem cells lose their pluripotency, proliferate and crowd together in a dense aggregate of chondrogenic cells (cartilage) at the location of chondrification. These chondrogenic cells differentiate into so-called chondroblasts, which then synthesize the cartilage extracellular matrix (ECM), consisting of a ground substance (proteoglycans, glycosaminoglycans for low osmotic potential) and fibers. The chondroblast is now a mature chondrocyte that is usually inactive but can still secrete and degrade the matrix, depending on conditions. Cell culture studies of excess Vitamin B inhibits the synthesis of chondroitin sulfate by chondrocytes and causes the inhibition of chondrogenesis in the developing embryo which may result in limb malformations. Chondrocytes undergo terminal differentiation when they become hypertrophic, which happens during endochondral ossification. This last stage is characterized by major phenotypic changes in the cell.
DNA replication licensing factor MCM6 is a protein that in humans is encoded by the MCM6 gene. MCM6 is one of the highly conserved mini-chromosome maintenance proteins (MCM) that is essential for the initiation of eukaryotic genome replication. The MCM complex consisting of MCM6 (this protein) and MCM2, 4 and 7 possesses DNA helicase activity, and may act as a DNA unwinding enzyme. The hexameric protein complex formed by the MCM proteins is a key component of the pre-replication complex (pre-RC) and may be involved in the formation of replication forks and in the recruitment of other DNA replication related proteins. The phosphorylation of the complex by CDC2 kinase reduces the helicase activity, suggesting a role in the regulation of DNA replication. Mcm 6 has recently been shown to interact strongly Cdt1 at defined residues, by mutating these target residues Wei et al. observed lack of Cdt1 recruitment of Mcm2-7 to the pre-RC.
Cl−indicators can be designed on the basis of endogenously expressed fluorescent proteins such as Yellow fluorescent protein (YFP). An advantage of endogenously expressed probes over dye-based probes is their ability to achieve cell-type-specificity by the choice of Promoter (genetics) promotor. YFP based indicators are mutated forms of Green fluorescent protein (GFP). YFP contains four point mutations and has a red-shifted excitation and emission spectrum compared with GFP. YFP fluorescence is sensitive to various small anions with relative potencies iodine > nitrate > chloride > bromide > formate > acetate. YFP sensitivity to these small anions results from ground-state binding near the chromophore, which apparently alters the chromophore ionization constant and hence the fluorescence emission. The fluorescence of YFP is sensitive to [Cl− ] and pH. The effect is fully reversible. YFP is excited at visible range and is a genetically encoded probe. YFP based Cl− sensors have rather low kinetics of Cl− association / dissociation. The half time association/dissociation constants for YFP mutant range from 50 ms (YFP-H148Q I152L) to 2 sec (YFP-H148Q V163S). If a fluorescent indicators is based on one fluorescent protein only, it doesn't allow for ratiometric measurements. Hence, a rationale for ratiometric fluorescent indicators results.
Possibly the most common use of affinity chromatography is for the purification of recombinant proteins. Proteins with a known affinity are protein tagged in order to aid their purification. The protein may have been genetically modified so as to allow it to be selected for affinity binding; this is known as a fusion protein. Protein tags include hexahistidine (His), glutathione-S-transferase (GST), maltose binding protein (MBP), and the Colicin E7 variant CL7 tag. Histidine tags have an affinity for nickel, cobalt, zinc, copper and iron ions which have been immobilized by forming coordinate covalent bonds with a chelator incorporated in the stationary phase. For elution, an excess amount of a compound able to act as a metal ion ligand, such as imidazole, is used. GST has an affinity for glutathione which is commercially available immobilized as glutathione agarose. During elution, excess glutathione is used to displace the tagged protein. CL7 has an affinity and specificity for Immunity Protein 7 (Im7) which is commercially available immobilized as Im7 agarose resin. For elution, an active and site-specific protease is applied to the Im7 resin to release the tag-free protein.
Screens for biologically relevant protein-protein interactions have been performed using Tandem Affinity Purification (TAP) with the SBP-Tag and Protein A, for interaction proteomics and transcription factor complexes with the SBP-Tag and Protein G, for proteins that interact with the Dengue Virus protein DENV-2 NS4A with the SBP-Tag and the Calmodulin Tag. and for proteins that interact with protein phosphatase 2A (PP2A) with the SBP-Tag and the hemagglutinin (HA)-tag.
Sources: en.wikipedia.org
Factors that affect absorption include: The way a drug product is designed and manufactured Its physical and chemical properties Other ingredients it contains The physiologic characteristics of the person taking the drug How the drug is stored Types of absorption in pharmacokinetics include the following: Instantaneous absorption: absorption is nearly immediate. A common example is bolus intravenous injection. Zero-order absorption: rate of absorption is constant. A common example is continuous intravenous infusion. First-order absorption: rate of absorption is proportional to the amount of drug remaining to be absorbed. Representative examples include typical cases of oral administration, subcutaneous injection, and intramuscular injection. Gastrointestinal transit time Flip–flop kinetics Absorption of Drugs
Intradialytic parenteral nutrition (IDPN) is a nutritional support therapy (medical nutrition therapy) for people on hemodialysis who have a difficult time maintaining adequate nutrition. It is administered directly into the bloodstream of patients with chronic kidney disease (CKD) in an effort to decrease the associated morbidity and mortality experienced in patients with kidney failure. IDPN contains protein (amino acids), carbohydrates (dextrose), and fats (lipids) in an attempt to meet a patient's weekly nutritional needs. Solutions can be individualized for each patient based on weight, needs, medical history and enteral intake.
The Swiss company GlycArt Biotechnology developed a system using CHO cells, where the cells were engineered to overexpress an enzyme called GnTIII. The effect of this overexpression is to block the formation of fucosylated oligosaccharides on the expressed antibodies. This technology was first reported in 1999 and was the basis of GlycArt Biotechnology. Roche acquired GlycArt in 2005 in order to acquire technology to afucosylate antibodies. GlycArt Biotechnology had been founded in 2000 as a spin-out company of the Swiss Federal Institute of Technology in Zurich. The first commercial product from the GlycArt acquisition was obinutuzumab, which as Gazyva gained FDA approval in November 2013 for the treatment of chronic lymphocytic leukemia. Kyowa Hakko Kirin's "Potelligent" platform uses a CHO cell line in which FUT8 has been knocked out, and which produces antibodies with little to no fucose in the Fc region. The company gained marketing approval in Japan in April 2012 for a monoclonal antibody drug called mogamulizumab which was developed using the platform. The Company's technology was first reported in 2004.
Arrestins (abbreviated Arr) are a small family of proteins important for regulating signal transduction at G protein-coupled receptors. Arrestins were first discovered in the late '80s as a part of a conserved two-step mechanism for regulating the activity of G protein-coupled receptors (GPCRs) in the visual rhodopsin system by Hermann Kühn, Scott Hall, and Ursula Wilden and in the β-adrenergic system by Martin J. Lohse and co-workers.
Sources: en.wikipedia.org
HPLC testing separates and quantifies components in a liquid sample. It is used to check identity, purity, concentration, or stability. The technique works best for compounds that dissolve and are not easily vaporized.
The pump maintains a steady flow rate and pressure, which keeps retention times reproducible. Pulsation or flow errors can shift peaks and distort quantitation. Modern pumps use feedback control to reduce these variations.
HPLC alone usually separates compounds but does not always identify them. Retention time matching with a known standard provides tentative identification. Coupling HPLC to mass spectrometry adds mass information that supports structural identification.
It measures the amounts and identities of compounds in liquid samples by separation and detection. Depending on the detector and reference standards, results can be qualitative or quantitative. The technique is used in fields such as pharmaceutical analysis, food safety, and environmental monitoring.