A practical reference on reversed-phase: what it is, how it behaves, what the literature reports, and where the honest uncertainties sit.
This page was last updated on 2026-02-01 and is reviewed periodically as new material appears.
Routine quality control monitors retention time shifts, baseline noise, system pressure, and peak shape. Trends can reveal column aging, mobile phase preparation errors, detector drift, or sample degradation. Corrective actions may include replacing the column, preparing fresh mobile phase, or recalibrating the detector. Stability testing often uses HPLC to measure parent compound loss and degradation product formation. Open questions remain about how accelerated stability results extrapolate to long-term storage under varied conditions.
Quality control for HPLC testing combines scheduled checks, documented procedures, and review of results. Before sample analysis, system suitability testing confirms that the instrument, column, and method meet predefined criteria. Common criteria include resolution between critical peaks, retention time precision, peak tailing, and theoretical plate count. Failure triggers investigation before results are reported. Records link raw data, calculations, instrument logs, and analyst identity to each batch, supporting audits and repeat analysis.
Method validation evaluates accuracy, precision, specificity, linearity, range, detection limit, quantitation limit, and robustness. Regulatory guidance for pharmaceuticals, foods, and environmental testing defines expected documentation and acceptance criteria. Verification confirms that a validated method works in a specific laboratory with its own instruments and reagents. Calibration curves use reference standards with known purity and traceability, while measurement uncertainty is estimated from validation data, control charts, and collaborative studies. The scope of validation depends on the method's intended use.
Several separation modes exist, including reversed-phase, normal-phase, ion-exchange, size-exclusion, and hydrophilic interaction liquid chromatography. Reversed-phase uses a nonpolar stationary phase with a polar mobile phase and is widely applied to small organic molecules. Gradient elution changes mobile phase composition during the run, while isocratic elution keeps it constant. Column chemistry, particle size, temperature, flow rate, and mobile phase pH all influence retention and resolution. Method development selects conditions that separate analytes from matrix components and from each other.
Detection commonly uses ultraviolet-visible absorbance, fluorescence, refractive index, or mass spectrometry. Ultraviolet detection depends on molecular chromophores that absorb light at specific wavelengths. Mass spectrometry provides mass information and sensitive quantification, often after electrospray ionization. Before sample batches, performance checks examine resolution, elution time repeatability, peak symmetry, and plate count. Matrix effects and co-elution remain recognized uncertainties; formal validation studies and orthogonal detection help address them. Detector choice depends on analyte properties and required sensitivity.
| Property | Value | Notes |
|---|---|---|
| Retention time RSD | ≤1% for five replicate injections | Typical criterion; method-specific limits apply. |
| Resolution | ≥1.5 between critical pair | Baseline separation is generally desired. |
| Tailing factor | ≤2.0 | Measures peak symmetry. |
| Theoretical plates | ≥2000 per column | Method-dependent; higher values indicate greater efficiency. |
| Peak area RSD | ≤2% for replicate injections | Reflects autosampler and detector precision. |
Quality control samples are inserted at intervals to monitor accuracy and precision throughout a batch. Blank samples detect contamination, while spiked samples assess recovery from the sample matrix. Calibration standards establish the relationship between detector response and concentration, and control samples are prepared independently from them whenever possible. Laboratories also participate in proficiency testing and maintain audit trails, instrument logs, and reagent records. Ongoing review of control charts can reveal trends before they cause out-of-specification results.
Method validation demonstrates that an HPLC procedure is suitable for its intended purpose. Common validation parameters include accuracy, precision, specificity, linearity, range, limit of detection, limit of quantification, and robustness. Accuracy reflects agreement with a reference value, while precision describes repeatability under defined conditions. Specificity shows whether the method can measure the analyte in the presence of impurities or matrix components. Validation documents are reviewed before a method is used for routine testing or regulatory submissions.
Instrumentation includes a solvent delivery system, an autosampler, a column oven, and one or more detectors. Reversed-phase columns with chemically modified silica are widely used, but normal-phase, ion-exchange, size-exclusion, and affinity modes exist for specific separations. Detectors may rely on ultraviolet absorbance, fluorescence, refractive index, or mass spectrometry. Column temperature, mobile phase composition, and flow rate are adjusted to improve resolution. System pressure is monitored because rising pressure can indicate column blockage or deteriorating packing.
Separation performance depends on particle size, pore size, column length, and the chemistry of the stationary phase. Smaller particles generally improve efficiency but require higher pressure and suitable instrumentation. The mobile phase often contains buffers and organic solvents that influence retention and selectivity. Testing labs select conditions based on the analytes, sample matrix, and required sensitivity. Method development frequently involves screening several columns and solvent mixtures before a final set of conditions is chosen.
Because their backbones are longer than those of normal peptides, β-peptides form disparate secondary structures. The alkyl substituents at both the α and β positions in a β-amino acid favor a gauche conformation about the bond between the α-carbon and β-carbon. This also affects the thermodynamic stability of the structure. Many types of helix structures consisting of β-peptides have been reported. These conformation types are distinguished by the number of atoms in the hydrogen-bonded ring that is formed in solution; 8-helix, 10-helix, 12-helix, 14-helix, and 10/12-helix have been reported. Generally speaking, β-peptides form a more stable helix than α-peptides. β-Peptides are stable against proteolytic degradation in vitro and in vivo, a potential advantage over natural peptides. β-Peptides have been used to mimic natural peptide-based antibiotics such as magainins, which are highly potent but difficult to use as drugs because they are degraded by proteolytic enzymes.
PI3K can also be activated by G protein-coupled receptors (GPCR), via G-protein βγ dimers or Ras which bind PI3K directly. In addition, the Gα subunit activates Src-dependent integrin signaling which can activate PI3K. Activated PI3K catalyses the addition of phosphate groups to the 3'-OH position the inositol ring of phosphoinositides (PtdIns), producing three lipid products, PI(3)P, PI(3,4)P2 and PI(3,4,5)P3: Phosphatidylinositol (PI) → PI 3-phosphate, (PI(4)P) → PI 3,4-bisphosphate, (PI(4,5)P2) → PI 3,4,5-triphosphate These phosphorylated lipids are anchored to the plasma membrane, where they can directly bind intracellular proteins containing a pleckstrin homology (PH) or FYVE domain. For example, the triphosphate form (PI(3,4,5)P3) binds Akt and phosphoinositide-dependent kinase 1 (PDK1) so they accumulate in close proximity at the membrane.
Arrestins (abbreviated Arr) are a small family of proteins important for regulating signal transduction at G protein-coupled receptors. Arrestins were first discovered in the late '80s as a part of a conserved two-step mechanism for regulating the activity of G protein-coupled receptors (GPCRs) in the visual rhodopsin system by Hermann Kühn, Scott Hall, and Ursula Wilden and in the β-adrenergic system by Martin J. Lohse and co-workers.
Alexander Butlerov Institute of Chemistry trains students for school chemical Olympiads of the Republic of Tatarstan and the Russian Federation. At various times, professors of the Institute of Chemistry headed Russian teams at International School Chemistry Olympiad among them were Andrey N. Vedernikov, Arkady I. Kuramshin and Igor A. Sedov; The old building of the Alexander Butlerov Institute of Chemistry since it was built in 1953, was not only a laboratory building of chemical faculty of Kazan University, at different times, it also placed historical-philological faculty of Kazan University, military department, some rooms were used as a hostel for young teachers and graduate students of the University.
Sources: en.wikipedia.org
Wheeler was awarded the Lab on a Chip Pioneers in Miniaturization Award (2017), an E.W.R. Steacie Fellowship from the Natural Sciences and Engineering Research Council of Canada (NSERC) (2015), a Connaught Foundation McLean Fellowship (2014), the Joseph Black Award from the Royal Society of Chemistry (2012), the Arthur F. Findeis Award from the American Chemical Society (2012), the Young Innovator Award in Analytical Chemistry (2011), and a Sloan Research Fellowship (2009). In January 2024, Wheeler was honored with the Ricardo Aroca Award, recognizing his contributions to analytical chemistry and advancing lab-on-a-chip techniques, particularly through the use of digital microfluidics (DMF), which enables precise manipulation of liquid droplets on electrode arrays. The Award is bestowed upon a scientist living in Canada who has made a notable contribution to the discipline of analytical chemistry while conducting research within the country.
Amino acids are the building blocks of protein and together they form the protein requirements in formula needed for growth and development. The amino acids are in the simplest form, making it easy for the body to process and digest. Amino acid-based formula may be considered hypoallergenic since it does not contain peptides that may trigger an immune response. Because infants and children have different nutritional needs, amino acid-based formulas are typically formulated either for infants 0–1 years of age or for children 1–10 years of age. Amino acid-based formulas may be used for those with cow's milk or soy protein allergy. However, most infants who suffer from food allergy respond well to extensively hydrolysed formulas, and only few of those with the most severe form of the illness require the use of amino acid-based formulas. It may also be used for other medical conditions requiring an amino acid-based diet, such as short bowel syndrome, and for transition from parenteral to enteral nutrition. Milk allergy Food allergy
APCs naturally have a role in fighting tumors, via stimulation of B and cytotoxic T cells to respectively produce antibodies against tumor-related antigen and kill malignant cells. Dendritic cells, presenting tumor-specific antigen to T cells, are key to this process. Cancer therapies have included treating the patient with increased numbers of dendritic cells or cancer-specific T cells. However, newer therapies have turned to genetically engineered artificial antigen-presenting cells designed to prime the immune system to attack malignant cells. Some artificial APCs are derived from human cells; others are acellular, containing MHC proteins, co-stimulatory molecules and the necessary peptides. The APC activator IMP321 is being tested in clinical trials to accelerate the immune reaction to eliminate metastatic breast cancer or melanoma. Antigen: protease degradation on YouTube – PMAP animation Antigen-Presenting+Cells at the U.S. National Library of Medicine Medical Subject Headings (MeSH)
Vaccine therapies are a type of specific active immunotherapy. Vaccine therapies deliver various agents that will lead to a specific immune response e.g. antibody development or CTL response. Tumor antigens have been a main target in specific active immunotherapy by way of vaccination. Tumor antigens are antigens produced by tumor cells and can be common among patients with the same cancer-type, or unique to a particular patient. Their specificity to malignant tumor cells makes tumor antigens ideal candidates for vaccination. Cancer vaccine C-Met#Active immunotherapy, Mantle cell lymphoma Immunotherapy,
Cell membranes are generally impermeable to charged or large, polar molecules because of the lipophilic fatty acyl chains comprising their interior. Many biologically important molecules, including a number of pharmaceutical agents, are organic weak acids that can cross the membrane in their protonated, uncharged form but not in their charged form (i.e., as the conjugate base). For this reason the activity of many drugs can be enhanced or inhibited by the use of antacids or acidic foods. The charged form, however, is often more soluble in blood and cytosol, both aqueous environments. When the extracellular environment is more acidic than the neutral pH within the cell, certain acids will exist in their neutral form and will be membrane soluble, allowing them to cross the phospholipid bilayer. Acids that lose a proton at the intracellular pH will exist in their soluble, charged form and are thus able to diffuse through the cytosol to their target. Ibuprofen, aspirin and penicillin are examples of drugs that are weak acids.
Sources: en.wikipedia.org
Once the heterologous protein has been fused with the bacterial cell surface protein, it is exposed to either an enzyme, a cell (expressing a target protein) or an antibody (usually fluorescently tagged), depending on the application of the experiment. The sample is then passed through a beam of light during FACS, in a very narrow stream of fluid so that only one cell can pass at a time, and the fluorescence emitted is detected. Information on the size of the cell can be obtained by the scattering of light and if binding of the heterologous protein with the target protein/cell has occurred, there will be more fluorescence emitted. Bacterial surface display can be used for a variety of applications. These include affinity-based screening, antibody epitope mapping, the identification of peptide substrates, the identification of cell-binding peptides and vaccine generation.
{\displaystyle \langle \Psi _{nlm_{l}m_{s}}|\mu |\Psi _{n'l'm_{l}'m_{s}'}\rangle } For example in the E1 transition, unless Δ l = ± 1, Δ ml = 0 or ± 1, Δ ms = 0, and Δ n = any integer, the equation above will yield a value equal to zero and the transition would be known as a “forbidden transition”. For example, this would occur for certain cases like when Δ l = 2. In this case, the transition would not be allowed and therefore would be much weaker than an allowed transition. These specific values for the changes in quantum numbers are known as the selection rules for the allowed transitions and are shown for common transitions in the table below: Cold vapour atomic fluorescence spectroscopy Atomic spectral line Prospects in Analytical Atomic Spectrometry – tendencies in five main branches of atomic spectrometry (absorption, emission, mass, fluorescence and ionization spectrometry) Learning by Simulations – various atomic absorption and emission spectra Atomic Spectroscopy: A Compendium of Basic Ideas, Notation, Data, and Formulas
The cellular response in signal transduction cascades involves alteration of the expression of effector genes or activation/inhibition of targeted proteins. Regulation of protein activity mainly involves phosphorylation/dephosphorylation events, leading to its activation or inhibition. It is the case for the vast majority of responses as a consequence of the binding of the primary messengers to membrane receptors. This response is quick, as it involves regulation of molecules that are already present in the cell. On the other hand, the induction or repression of the expression of genes requires the binding of transcriptional factors to the regulatory sequences of these genes. The transcriptional factors are activated by the primary messengers, in most cases, due to their function as nuclear receptors for these messengers. The secondary messengers like DAG or Ca2+ could also induce or repress gene expression, via transcriptional factors. This response is slower than the first because it involves more steps, like transcription of genes and then the effect of newly formed proteins in a specific target. The target could be a protein or another gene.
Lewis acids have been classified in the ECW model and it has been shown that there is no one order of acid strengths. The relative acceptor strength of Lewis acids toward a series of bases, versus other Lewis acids, can be illustrated by C-B plots. It has been shown that to define the order of Lewis acid strength at least two properties must be considered. For Pearson's qualitative HSAB theory the two properties are hardness and strength while for Drago's quantitative ECW model the two properties are electrostatic and covalent. Monoprotic acids, also known as monobasic acids, are those acids that are able to donate one proton per molecule during the process of dissociation (sometimes called ionization) as shown below (symbolized by HA):
Sources: en.wikipedia.org
System suitability is typically performed before each batch or according to the validated method and laboratory procedure. Some long runs include periodic checks during analysis. The required frequency depends on regulatory expectations and method performance.
Retention time drift can result from changes in mobile phase composition, column temperature, pump flow, or column age. A gradual shift often points to column degradation. A sudden shift may indicate a leak, mixing error, or incorrect mobile phase.
Retention time alone cannot confirm identity because different compounds may elute at similar times. Coupling HPLC with mass spectrometry or comparing against authenticated standards increases confidence. Confirmation usually requires orthogonal data.
HPLC separates and quantifies compounds in a liquid sample. Detectors produce a response proportional to the amount of a compound passing through the flow cell. Identification by retention time requires comparison with a known standard.