The short version of retention time fits in a sentence. The long version — which is the one that helps — is below.
Reviewed 2025-09-26. Anything still debated is marked as such rather than presented as settled.
Reversed-phase chromatography dominates modern HPLC testing, using a nonpolar stationary phase such as chemically bonded octadecyl groups and a polar mobile phase of water mixed with organic solvent. Analytes partition between the mobile and stationary phases according to hydrophobicity. Gradient elution changes the mobile phase composition over time to separate compounds with a wide range of retention. Isocratic elution keeps the composition constant and is simpler for routine assays. Column temperature, pH, and flow rate influence selectivity, peak shape, and retention time, so these parameters are controlled during a validated method.
Detection in HPLC testing commonly relies on ultraviolet-visible absorbance, fluorescence, refractive index, or mass spectrometry. A diode array detector records full spectra across a wavelength range, which helps identify co-eluting peaks. Mass spectrometry provides mass-to-charge ratios and can confirm molecular identity at low concentrations. The choice of detector depends on analyte structure, required sensitivity, and whether quantitation or identification is the goal. No single detector works for every compound, and method development often compares responses before selecting one.
Routine HPLC testing depends on controlled reagents, calibrated instruments, and documented procedures. Columns degrade over time, so retention times and peak shapes are monitored for drift. Mobile phases are filtered and degassed to prevent pump damage and detector noise. Reference standards must be traceable and stored under suitable conditions. Data handling systems record injections, calculations, and audit trails. Quality control samples interspersed with unknowns help detect errors during a run.
Developing an HPLC method begins with defining the purpose, such as quantifying a main component, measuring impurities, or confirming identity. Analysts select separation mode, column, mobile phase, detection, and sample preparation based on analyte properties and matrix. Experiments vary solvent strength, pH, buffer type, and temperature to achieve resolution between critical peaks. The goal is a robust method that produces reliable results across instruments and operators. Method development often involves trial runs and statistical optimization.
Validation demonstrates that a method is suitable for its intended use. Typical performance characteristics include accuracy, precision, specificity, linearity, range, limit of detection, limit of quantitation, and robustness. Regulators and standards organizations provide frameworks, but specific requirements depend on the application and jurisdiction. System suitability tests are run before sample analysis to confirm resolution, peak symmetry, retention time repeatability, and sensitivity. A validated method is not permanently fixed; changes may require partial or full revalidation.
| Property | Value | Notes |
|---|---|---|
| Separation mode | Reversed-phase | Most common for neutral and moderately polar analytes |
| Column particle size | 3–5 µm | Smaller particles improve resolution but raise backpressure |
| Mobile phase pH range | 2–8 | Silica-based columns may degrade outside this range |
| Typical flow rate | 1.0–2.0 mL/min | For analytical columns with 4.6 mm internal diameter |
| Common synonyms | HPLC, LC, high-pressure liquid chromatography | High-performance liquid chromatography is the standard expansion |
Several separation modes exist, including reversed-phase, normal-phase, ion-exchange, size-exclusion, and hydrophilic interaction liquid chromatography. Reversed-phase uses a nonpolar stationary phase with a polar mobile phase and is widely applied to small organic molecules. Gradient elution changes mobile phase composition during the run, while isocratic elution keeps it constant. Column chemistry, particle size, temperature, flow rate, and mobile phase pH all influence retention and resolution. Method development selects conditions that separate analytes from matrix components and from each other.
Detection commonly uses ultraviolet-visible absorbance, fluorescence, refractive index, or mass spectrometry. Ultraviolet detection depends on molecular chromophores that absorb light at specific wavelengths. Mass spectrometry provides mass information and sensitive quantification, often after electrospray ionization. Before sample batches, performance checks examine resolution, elution time repeatability, peak symmetry, and plate count. Matrix effects and co-elution remain recognized uncertainties; formal validation studies and orthogonal detection help address them. Detector choice depends on analyte properties and required sensitivity.
Before amylin deposition was associated with diabetes, already in 1901, scientists described the phenomenon of "islet hyalinization", which could be found in some cases of diabetes. A thorough study of this phenomenon was possible much later. In 1986, the isolation of an aggregate from an insulin-producing tumor was successful, a protein called IAP (Insulinoma Amyloid Peptide) was characterized, and amyloids were isolated from the pancreas of a diabetic patient, but the isolated material was not sufficient for full characterization. This was achieved only a year later by two research teams whose research was a continuation of the work from 1986.
Signal transduction is realized by activation of specific receptors and consequent production/delivery of second messengers, such as Ca2+ or cAMP. These molecules operate as signal transducers, triggering intracellular cascades and in turn amplifying the initial signal. Two main signal transduction mechanisms have been identified, via nuclear receptors, or via transmembrane receptors. In the first one, first messenger cross through the cell membrane, binding and activating intracellular receptors localized at nucleus or cytosol, which then act as transcriptional factors regulating directly gene expression. This is possible due to the lipophilic nature of those ligands, mainly hormones. In the signal transduction via transmembrane receptors, the first messenger binds to the extracellular domain of transmembrane receptor, activating it. These receptors may have intrinsic catalytic activity or may be coupled to effector enzymes, or may also be associated to ionic channels. Therefore, there are four main transmembrane receptor types: G protein coupled receptors (GPCRs), tyrosine kinase receptors (RTKs), serine/threonine kinase receptors (RSTKs), and ligand-gated ion channels (LGICs). Second messengers can be classified into three classes:
The following table illustrates variability in reference ranges of serum prolactin between some commonly used assay methods (as of 2008), using a control group of healthy health care professionals (53 males, age 20–64 years, median 28 years; 97 females, age 19–59 years, median 29 years) in Essex, England: An example of the use of the above table is, if using the Centaur assay to estimate prolactin values in μg/L for females, the mean is 168 mIU/L (7.92 μg/L) and the reference range is 71–348 mIU/L (3.35–16.4 μg/L). Hyperprolactinaemia, or excess serum prolactin, is associated with hypoestrogenism, anovulatory infertility, oligomenorrhoea, amenorrhoea, unexpected lactation and loss of libido in women and erectile dysfunction and loss of libido in men. Causes of Elevated Prolactin Levels
Bont possesses no superhuman abilities, but he occasionally used Mutant Growth Hormone, a substance that temporarily enhanced his speed and strength and caused his eyes to emit a green glow. Sigourney Weaver portrays a female version of Alexander Bont, primarily known as Alexandra, in The Defenders. This version is the leader of the Hand. Alexandra is described as an "adversary" rather than a villain and was intended to be portrayed sympathically as a supporting character in Elektra Natchios' story. Alexandra is one of the five "fingers" of the Hand, who all gained immortality using the healing powers of qi. Following the death of Elektra, Alexandra resurrects her to create the ancient weapon Black Sky, which is prophesied to destroy all enemies of the Hand. Alexandra intends to use Elektra to steal the Iron Fist from Danny Rand. However, Elektra regains her memories of her previous life and kills Alexandra, claiming leadership of the Hand. http://www.marvunapp.com/Appendix4/bontalexander.htm http://www.imdb.com/title/tt1784594/
GPCRs become desensitized when exposed to their ligand for a long period of time. There are two recognized forms of desensitization: 1) homologous desensitization, in which the activated GPCR is downregulated; and 2) heterologous desensitization, wherein the activated GPCR causes downregulation of a different GPCR. The key reaction of this downregulation is the phosphorylation of the intracellular (or cytoplasmic) receptor domain by protein kinases. Cyclic AMP-dependent protein kinases (protein kinase A) are activated by the signal chain coming from the G protein (that was activated by the receptor) via adenylate cyclase and cyclic AMP (cAMP). In a feedback mechanism, these activated kinases phosphorylate the receptor. The longer the receptor remains active the more kinases are activated and the more receptors are phosphorylated. In β2-adrenoceptors, this phosphorylation results in the switching of the coupling from the Gs class of G-protein to the Gi class. cAMP-dependent PKA mediated phosphorylation can cause heterologous desensitisation in receptors other than those activated.
Sources: en.wikipedia.org
One mechanism through which BDNF appears to maintain elevated levels of neuronal excitation is through preventing GABAergic signaling activities. While glutamate is the brain's major excitatory neurotransmitter and phosphorylation normally activates receptors, GABA is the brain's primary inhibitory neurotransmitter and phosphorylation of GABAA receptors tend to reduce their activity. Blockading BDNF signaling with a tyrosine kinase inhibitor or a PKC inhibitor in wild type mice produced significant reductions in spontaneous action potential frequencies that were mediated by an increase in the amplitude of GABAergic inhibitory postsynaptic currents (IPSC). Similar effects could be obtained in BDNF knockout mice, but these effects were reversed by local application of BDNF. This suggests BDNF increases excitatory synaptic signaling partly through the post-synaptic suppression of GABAergic signaling by activating PKC through its association with TrkB. Once activated, PKC can reduce the amplitude of IPSCs through to GABAA receptor phosphorylation and inhibition. In support of this putative mechanism, activation of PKCε leads to phosphorylation of N-ethylmaleimide-sensitive factor (NSF) at serine 460 and threonine 461, increasing its ATPase activity which downregulates GABAA receptor surface expression and subsequently attenuates inhibitory currents.
c7orf26 (accession: NM_024067 / NP_076972; alias: MGC-2178) is located on the long arm of chromosome 7 (7p22.1), starting at 6590021 and ending at 6608726. The c7orf26 gene spans 2178 base pairs and is orientated on the + strand. The coding region is made up of a protein sequence measuring 449 amino acids long. It is divided into 6 transcripts containing a total of 24 exons on the forward strand and has 5952 unique Single Nucleotide Polymorphisms (SNPs). Genes ZDHHC4, ZNF853 and ZNF316 neighbor c7orf26 on chromosome 7. Gene ZDHHC4 is a zinc-finger protein involved with cytochrome-c oxidase activity and protein-cysteine S-palmitoyltransferase activity and has overlapping regions with c7orf26. Gene GRID2IP lies upstream by >2000 bp of c7orf26, and is heavily involved with in synaptogenesis and synaptic plasticity. c7orf26 is highly expressed in lymphatic, reproductive, and nervous tissue. These include the brain (frontal and occipital cortex), thymus glands, salivary glands, endometrium, cervix, and prostate. It is intermediately expressed in the lungs.
After earning his doctorate in biochemistry, Lehninger held various faculty positions at the University of Wisconsin–Madison and the University of Chicago. In 1952, he went to the Johns Hopkins School of Medicine, assuming the title of DeLamar Professor of the Department of Biological Chemistry. He served in this position until 1978, when he was appointed to the role of University Professor of Medical Sciences. He held this title until his death in 1986. 1948 – Paul-Lewis Award in Enzyme Chemistry 1951 – Guggenheim Fellowship 1956 – Elected to the National Academy of Sciences 1959 – Elected to the American Academy of Arts and Sciences 1969 – Remsen Award of the American Chemical Society 1970 – American Philosophical Society 1986 – Passano Foundation Award Forthcoming in New Dictionary of Scientific Biography
Advanced product quality planning is a process developed in the late 1980s by a commission of experts who gathered around the 'Big Three' of the US automobile industry: Ford, GM, and Chrysler. Representatives from the three automotive original equipment manufacturers (OEMs) and the Automotive Division of American Society for Quality Control (ASQC) created the Supplier Quality Requirement Task Force for developing a common understanding on topics of mutual interest within the automotive industry. This commission worked five years to analyze the then-current automotive development and production status in the US, Europe, and especially in Japan. At the time, the Japanese automotive companies were successful in the US market. APQP is utilized by US automakers and some of their affiliates. Tier 1 suppliers are typically required to follow APQP procedures, techniques, and are also typically required to be audited and registered to IATF 16949. This methodology is also being used in other manufacturing sectors. The Automotive Industry Action Group (AIAG) is a non-profit association of automotive companies founded in 1982. The basis for the process control plan is described in AIAG's APQP manual These include:
Sources: en.wikipedia.org
1-Heneicosanol is the C21 member of the series of linear, saturated primary alcohols derived formally from heneicosane by substitution of a terminal hydrogen atom with a hydroxyl group. It is classified as a long-chain fatty alcohol. Commercial material is typically obtained as a white powder or low-melting wax with a reported melting range of about 68–71 °C. A safety data compilation and estimation methods indicate a high normal boiling point of around 366 °C at 760 mmHg, consistent with its long carbon chain. The compound has very low solubility in water and a high octanol/water partition coefficient (log P), reflecting its pronounced hydrophobic character.
The entries in BTO are updated bi-annually as part of the major update of BRENDA. It is available via the BRENDA website in the category “Ontology Explorer”. The enzyme source terms can be searched via the BTO query form. As a result, the user receives a list of EC numbers which are directly connected to the enzyme information of BRENDA. It is also possible to search via the BRENDA “Source Tissue” search form (“Classic View”). The result page displays all enzymes which are isolated or detected in the searched tissue term, directly linked to BTO. BTO and BRENDA are freely accessible for academic users. It can be freely downloaded via the “Ontology Explorer” of the BRENDA website or in the OBO format from “Obofoundry”. BTO (BRENDA Tissue Ontology) BRENDA Ontology Explorer BRENDA-website ExplorEnz – Enzyme Nomenclature Obofoundry Gene Ontology Consortium EBI-EMBL Bioportal des National Center for Biomedical Ontology, Stanford, USA
It is synthesized from lathosterol by the enzyme lathosterol oxidase (lathosterol 5-desaturase). This is the next-to-last step of cholesterol biosynthesis. Defective synthesis results in the human inherited disorder lathosterolosis resembling Smith–Lemli–Opitz syndrome. Mice where this gene has been deleted lose the ability to increase vitamin D3 in the blood following UV exposure of the skin. The skin consists of two primary layers: an inner layer, the dermis, comprising largely connective tissue, and an outer, thinner epidermis. The thickness of the epidermis ranges from 0.04 mm to greater than 0.6 mm. The epidermis comprises five strata; from outer to inner, they are the stratum corneum, stratum lucidum, stratum granulosum, stratum spinosum, and stratum basale. The highest concentrations of 7-dehydrocholesterol are found in the epidermal layer of skin—specifically in the stratum basale and stratum spinosum. The production of pre-vitamin D3 is, therefore, greatest in these two layers.
Sources: en.wikipedia.org
HPLC testing separates and quantifies components in a liquid sample. It is used to check identity, purity, concentration, or stability. The technique works best for compounds that dissolve and are not easily vaporized.
The pump maintains a steady flow rate and pressure, which keeps retention times reproducible. Pulsation or flow errors can shift peaks and distort quantitation. Modern pumps use feedback control to reduce these variations.
HPLC alone usually separates compounds but does not always identify them. Retention time matching with a known standard provides tentative identification. Coupling HPLC to mass spectrometry adds mass information that supports structural identification.
It is a set of checks performed before or during an HPLC run to confirm the system works as expected. Parameters may include resolution, tailing factor, theoretical plates, and retention time precision. Failure can trigger maintenance, method adjustment, or repeat analysis.