reversed-phase raises a handful of sensible questions. This page answers them in order, starting with the fundamentals and moving to applications.
This page was last updated on 2026-08-01 and is reviewed periodically as new material appears.
Most routine HPLC testing uses reversed-phase columns, where the stationary phase is nonpolar and the mobile phase is a polar mixture such as water with an organic solvent. Analytes partition between the two phases according to polarity, size, and charge. Gradients that change solvent composition over time can separate compounds with broad retention ranges. Isocratic conditions keep solvent composition constant and suit simpler mixtures. The choice of column chemistry, pH, and temperature affects selectivity and peak shape.
Detection in HPLC testing commonly relies on ultraviolet-visible absorbance, fluorescence, refractive index, or mass spectrometry. UV detection is widely used because many organic compounds absorb light, but it requires a chromophore. Mass spectrometry provides mass-based identification and high sensitivity for trace analytes. Each detector has trade-offs in selectivity, cost, and compatibility with mobile phases. Quantification typically uses calibration curves prepared from reference standards. Results are reported as concentration, purity, or presence above a limit.
HPLC testing separates dissolved compounds by passing a liquid sample through a column packed with stationary phase. A pump delivers mobile phase at controlled flow, and the sample components interact differently with stationary and mobile phases. Compounds that spend more time in mobile phase elute earlier; those retained by stationary phase elute later. Detectors record elution as peaks, and peak area or height relates to amount. This mechanism underpins quantitative analysis of mixtures.
High-performance liquid chromatography is an analytical technique that separates components in a liquid sample. A pump moves a liquid mobile phase through a column packed with a solid stationary phase. Compounds interact differently with both phases and travel at different rates, leaving the column at distinct retention times. A detector records these arrivals as peaks on a chromatogram. The resulting pattern supports identification and quantification of substances in mixtures. Modern instruments use high pressure to force solvent through small particles, which improves speed and resolution compared with older low-pressure liquid chromatography methods.
Separation in HPLC depends on the chemistry of the stationary phase, the composition of the mobile phase, and the physical properties of the column. Reverse-phase separations use a nonpolar stationary phase and a polar mobile phase, and they are common for many organic compounds. Ion-exchange, size-exclusion, and normal-phase modes serve other classes of analytes. Gradient elution changes solvent strength over time, while isocratic elution holds it constant. Flow rate, temperature, particle size, and column length all influence peak shape and resolution. Detection may use ultraviolet absorbance, fluorescence, refractive index, or mass spectrometry, depending on the analyte and the required sensitivity.
| Property | Value | Notes |
|---|---|---|
| Separation mode | Reversed-phase | Nonpolar stationary phase with polar mobile phase |
| Typical column particle size | 3–5 µm | Smaller particles improve resolution but raise pressure |
| Typical flow rate | 0.5–2.0 mL/min | Depends on column dimensions and pressure limits |
| Common detection | UV-Vis absorbance | Requires analytes with chromophores |
| Typical run time | 5–30 min | Varies with method, gradient, and sample complexity |
High-performance liquid chromatography is an analytical technique that separates components of a liquid sample by passing it through a packed column under pressure. A pump delivers a mobile phase at a controlled flow rate, and an injector introduces the sample into the stream. Differences in interaction with the stationary phase cause analytes to migrate at different rates. Detectors record elution as peaks, and a data system converts signals into a chromatogram. The method is suited to compounds that dissolve in a liquid and are not volatile enough for gas chromatography.
Reversed-phase chromatography dominates modern HPLC testing, using a nonpolar stationary phase such as chemically bonded octadecyl groups and a polar mobile phase of water mixed with organic solvent. Analytes partition between the mobile and stationary phases according to hydrophobicity. Gradient elution changes the mobile phase composition over time to separate compounds with a wide range of retention. Isocratic elution keeps the composition constant and is simpler for routine assays. Column temperature, pH, and flow rate influence selectivity, peak shape, and retention time, so these parameters are controlled during a validated method.
Detection in HPLC testing commonly relies on ultraviolet-visible absorbance, fluorescence, refractive index, or mass spectrometry. A diode array detector records full spectra across a wavelength range, which helps identify co-eluting peaks. Mass spectrometry provides mass-to-charge ratios and can confirm molecular identity at low concentrations. The choice of detector depends on analyte structure, required sensitivity, and whether quantitation or identification is the goal. No single detector works for every compound, and method development often compares responses before selecting one.
Routine quality control uses system suitability, blank injections, check standards, and control samples to detect drift or contamination. System suitability criteria may specify minimum resolution, maximum tailing factor, and a permitted range for repeated injections. Blank injections reveal carryover or solvent contamination, while check standards confirm calibration accuracy over a batch. Control samples with known analyte levels can show whether results remain within statistical limits. When a control result falls outside limits, the analyst investigates the cause and may invalidate affected results before repeating the batch.
Documentation and traceability are central to regulated HPLC testing. Records typically include instrument logs, column history, mobile-phase preparation, sample preparation, injection sequences, raw chromatograms, and audit trails. Electronic systems may require user access controls, time-stamped changes, and backup procedures. Training records show that analysts are qualified for assigned methods. Audits and inspections check whether written procedures match actual practice and whether deviations are documented. These controls support reproducibility and allow results to be reconstructed if questions arise later.
Routine quality control monitors retention time shifts, baseline noise, system pressure, and peak shape. Trends can reveal column aging, mobile phase preparation errors, detector drift, or sample degradation. Corrective actions may include replacing the column, preparing fresh mobile phase, or recalibrating the detector. Stability testing often uses HPLC to measure parent compound loss and degradation product formation. Open questions remain about how accelerated stability results extrapolate to long-term storage under varied conditions.
Quality control for HPLC testing combines scheduled checks, documented procedures, and review of results. Before sample analysis, system suitability testing confirms that the instrument, column, and method meet predefined criteria. Common criteria include resolution between critical peaks, retention time precision, peak tailing, and theoretical plate count. Failure triggers investigation before results are reported. Records link raw data, calculations, instrument logs, and analyst identity to each batch, supporting audits and repeat analysis.
Method validation evaluates accuracy, precision, specificity, linearity, range, detection limit, quantitation limit, and robustness. Regulatory guidance for pharmaceuticals, foods, and environmental testing defines expected documentation and acceptance criteria. Verification confirms that a validated method works in a specific laboratory with its own instruments and reagents. Calibration curves use reference standards with known purity and traceability, while measurement uncertainty is estimated from validation data, control charts, and collaborative studies. The scope of validation depends on the method's intended use.
System suitability testing is performed before and during analytical runs to confirm that the instrument and method are working as expected. Typical checks include retention time, peak area precision, resolution between critical pairs, tailing factor, and theoretical plate count. Acceptance criteria are set in the method or pharmacopeial monograph. If a suitability check fails, the run may be rejected and the instrument or sample preparation may need investigation. This practice helps prevent release of data from a system that has drifted out of control.
Quality control samples are inserted at intervals to monitor accuracy and precision throughout a batch. Blank samples detect contamination, while spiked samples assess recovery from the sample matrix. Calibration standards establish the relationship between detector response and concentration, and control samples are prepared independently from them whenever possible. Laboratories also participate in proficiency testing and maintain audit trails, instrument logs, and reagent records. Ongoing review of control charts can reveal trends before they cause out-of-specification results.
Because lipopolysaccharides are potent inflammatory agents, and the action of antibiotics can result in the release of these compounds, the binding capacity of BPI was explored as a possible means of reducing injury. Xoma Ltd. developed a recombinant 21kDa portion of the BPI molecule called rBPI21, NEUPREX, or opebecan. In a trial, it was found to decrease the mortality of Gram-negative bacterial-induced sepsis. Studies suggest that its binding activity is not the means by which it mediates its protective effect. Studies show biological effects with Gram-positive bacteria and even in infection by the protozoan, Toxoplasma gondii. The N-terminal portion of murine BPI (199 amino acids) genetically fused to Halobacterium sp. NRC-1 GvpC protein was bound to the surface of gas vesicle nanoparticles (GVNPs) and tested for protective activity using a murine model of endotoxic shock. Depending on the time of delivery and exposure to lethal concentrations of lipopolysaccharide (LPS) and D-galactosamine, the treatment resulted in increased survival and reduced symptoms of inflammation, including inflammatory anemia, recruitment of neutrophils, liver apoptosis as well as increased pro-inflammatory serum cytokine levels. When administered via footpad and before LPS exposure, there was 100% survival of the experimental cohort.
Seven genes encode seven distinct 14-3-3 proteins in most mammals (See Human genes below) and 13–15 genes in many higher plants, though typically in fungi they are present only in pairs. Protists have at least one. Eukaryotes can tolerate the loss of a single 14-3-3 gene if multiple genes are expressed, but deletion of all 14-3-3s (as experimentally determined in yeast) results in death. 14-3-3 proteins are structurally similar to the Tetratrico Peptide Repeat (TPR) superfamily, which generally have 9 or 10 alpha helices, and usually form homo- and/or hetero-dimer interactions along their amino-termini helices. These proteins contain a number of known common modification domains, including regions for divalent cation interaction, phosphorylation & acetylation, and proteolytic cleavage, among others established and predicted. 14-3-3 binds to peptides. There are common recognition motifs for 14-3-3 proteins that contain a phosphorylated serine or threonine residue, although binding to non-phosphorylated ligands has also been reported. This interaction occurs along a so-called binding groove or cleft that is amphipathic in nature. To date, the crystal structures of six classes of these proteins have been resolved and deposited in the public domain.
Anne Ephrussi studied biology at Harvard University in the Department of Biochemistry and Molecular Biology from where she graduated in 1979. She continued to do her PhD at the Massachusetts Institute of Technology (MIT) in the group of Susumu Tonegawa where she received her doctoral degree in 1985. Ephrussi performed postdoctoral research at Harvard University in the lab of Thomas Maniatis from 1986 to 1989 and at the Whitehead Institute for Biomedical Research with Ruth Lehmann from 1989 to 1992. Since 1992, Anne Ephrussi has been a group leader at the European Molecular Biology Laboratory (EMBL). She became the head of EMBL International Centre for Advanced Training in 2005. She served as Associate Dean (1999 - 2005) and Dean (2005 - 2008) of Graduate Studies of the EMBL International PhD program and as head of the developmental biology unit (2007-2021). She is part of numerous international Scientific Advisory Boards and Panels, organizes international conferences and scientific meetings and evaluates research grant and fellowship applications for a variety of renowned funding bodies.
Sources: en.wikipedia.org
Because of its central role in controlling eukaryotic gene expression, P-TEFb is subject to stringent regulation at the level of transcription of the genes encoding the subunits, translation of the subunit mRNAs, turnover of the subunits, and also by an unusual mechanism involving the 7SK snRNP. As shown in Figure 3 P-TEFb is held in the 7SK snRNP by the double stranded RNA binding protein HEXIM (HEXIM1 or HEXIM2 in humans). HEXIM bound to 7SK RNA or any double stranded RNA binds to P-TEFb and inhibits the kinase activity. Two other proteins are always found associated with 7SK RNA. The methyl phosphase capping enzyme MEPCE puts a methyl group on the gamma phosphate of the first nucleotide of the 7SK RNA and the La related protein LARP7 binds to the 3' end of 7SK. When P-TEFb is extracted from the 7SK snRNP, 7SK RNA undergoes a conformation change, HEXIM is ejected and hnRNPs take the place of the factors removed. The re-sequestration of P-TEFb requires another rearrangement of the RNA, binding of HEXIM and then P-TEFb. In rapidly growing cells the 7SK snRNP is the predominant form of P-TEFb. For review.
Ana María Muñoz Jauregui (born 1969, Lima) is a Peruvian pharmacist, biochemist and nutritionist. She has served as Rector and, since 2023, as the Vice Rector of research at San Ignacio de Loyola University (USIL). Muñoz has authored numerous publications and received national and international awards, such as silver, gold medals and semi-grand prize wins at the International KIWIE Award. Muñoz, was born in Lima, Peru. In 1996, she attended the National University of San Marcos (UNMSM), where she earned her pharmaceutical degree. While studying, she developed an interest in the field of nutrition. She earned a master's degree in biochemistry and nutrition, and earned a PhD in Pharmacy and Biochemistry from the National University of San Marcos (UNMSM) in 2006.
ASQ provides its members with certification, training, publications, conferences, and other services. ASQ is a founding partner of the American Customer Satisfaction Index (ACSI), a quarterly economic indicator. Since 1989, ASQ has administered the annual Malcolm Baldrige National Quality Award. The ASQ also gives the Dorian Shainin Medal, which is awarded annually for the "Development and Application of Creative or Unique Statistical Approaches in the Solving of Problems Relative to the Quality of Product or Service".
Sources: en.wikipedia.org
It separates components in a liquid sample and measures their amounts using a detector. Results can indicate concentration, purity, or identity based on retention time and detector response. The technique works for mixtures that can be dissolved and filtered.
It offers high resolution, reproducibility, and compatibility with many sample types. A single run can separate and quantify multiple analytes. It is common in pharmaceutical, food, environmental, and industrial laboratories.
Samples must be soluble in a suitable mobile phase and free of particles that can block the column. Detector response depends on analyte structure, so some compounds need derivatization or alternative detection. Complex matrices may require extensive sample preparation.
HPLC testing measures the presence and amount of one or more compounds in a liquid sample. It separates mixture components and records detector responses as peaks, which are compared with reference standards. Results are usually reported as concentrations or relative percentages.